SKIP TO CONTENT

Loopify

  • Plugin
  • Skill

Check a repeating agent job in one line.

  • No babysitting

    One command prints one of six verdicts, such as OK, NEEDS YOU or STALE.

  • Fewer stuck ticks

    A tick is one run of the job. loopify lists the commands to allow first.

  • Stops by itself

    The line carries a stop rule. Every /loop ends after 7 days.

Works with: Made for the /loop command of Claude Code. Install tested: Claude Code, Codex, Cursor, Gemini CLI, GitHub Copilot, OpenCode. Not tied to one model: Markdown and Python.

Pick your agent

npx skills add Aboudjem/loopify -g

Works in more than 70 agents: pick yours in the menu. Supported agents (new tab)Installs for all your projects. Only this project: drop -g.Its page on skills.sh (new tab)

Limit: The loop lives in your open session and ends after 7 days.

github.com/Aboudjem/loopify (new tab)Version 1.2.4

What it does

  • Know at a glance. One status line says OK, NEEDS YOU, STALE or one of three other verdicts.
  • See every tick. Each tick writes one entry to TICKS.md.
  • Catch a dead loop. A missing entry shows as STALE when the interval is known.
  • Know it will end. The stop rule is in the line, and every loop expires at 7 days.
  • Fewer stuck ticks. It prints the commands to pre-approve, such as gh pr view.

How it works

  1. 1. Describe the job. Type /loopify in Claude Code and say what should repeat.
  2. 2. Paste the line into /loop. Claude runs one round now, then one at each interval.
  3. 3. The loop ends when the stop rule is met or when it reaches the tick cap.
  4. 4. Check it in one line. The status command reads TICKS.md and gives a verdict.

Example

The line you paste, then the status command on the example that ships in the repository. Both come from the README.

/loop 20m Run one cycle of /Users/you/acme/.loop/pr-babysitter.md · read it first, obey its stop rule (30 ticks or the PR merges), log the tick.

$ python3 skills/loopify/scripts/loop_status.py examples/loop-state/pr-babysitter --now 2026-09-01T09:50
STATUS: NEEDS YOU · tick 7/30 · last tick 2026-09-01T09:40 (changed, 10 min ago) · 2 queued

Do next:
1. QUEUE.md, tick 4: Post the drafted reply on the `fetchAll` rename thread of PR #412

More ways to install

Claude Code plugin

claude plugin marketplace add Aboudjem/10x
claude plugin install loopify@10x

Agent skill, for Cursor, Codex and other agents

npx skills add Aboudjem/loopify

Limits

  • No evaluator checks the loop, so the log is the only proof that it did the right thing.
  • The loop lives in the session you paste it into. Close the terminal and it stops.
  • A tick that hits a permission prompt waits there for your answer.
  • The line is a Claude Code /loop line. In another agent, an outside scheduler runs each tick.
Good for
Watching a pull request or sorting new bug reports while your session stays open.
Not for
One big task with a clear end: Goalify is the tool for that.

Questions

What is Loopify?

Loopify is an open-source skill for jobs that repeat. It writes the prompt for Claude Code's /loop command, and every run writes to a log.

Which agents does Loopify work with?

Install tested on 17 November 2026: Claude Code, Cursor, Codex, GitHub Copilot and Gemini CLI. The /loop line is for Claude Code; elsewhere, an outside scheduler runs each tick.

What is the difference between Loopify and Goalify?

Goalify is for a job that finishes: one big task and one definition of done. Loopify is for a job that repeats.

Is Loopify free?

Yes, it is open source under the MIT license. It is one skill folder with three standard-library Python scripts.